DIY Rustic Star Decoration from Reclaimed Pallet Wood

Today it’s rainy and gross outside.  Storms are brewing, we’re under tornado watch – in short, it’s wet and windy.  In my opinion, the only things these kinds of days are good for (besides nourishing Mother Earth) are fun projects, deep cleaning, and organizing.  It’s been awhile since I did any of the latter, and I thought I’d start with my blog.  I’ve chosen a new layout, which I am MUCH happier with, and while looking through some of my old posts, I realized that I had never posted this project that I did last fall.  It was so much fun, and it’s so cute, I can’t believe I never shared it with you all.

The store where I worked at the time had a bunch of pallets they were ready to throw out, so I brought a couple home.  One is in pieces; the other is still taking up space in our garage.   Nonetheless, I did get this project done pretty much right off the bat, but I haven’t had the opportunity to find somewhere to display it yet – that’s a plan for this weekend.

What I made was a rustic star out of bits and pieces of the pallet, some wood glue, and some nuts and bolts.  Very simple, very easy – once you’ve gotten the pallet apart.  If you’re looking for new ways to add to your outdoor decor this spring and summer, this is the perfect project.  It’s quick and easy, and you can have it out before the daffodils are blooming!

Materials

  • 5 pieces pallet wood, or any reclaimed wood, all about the same length and width.  Mine measure approximately 30″ x 3-1/2″ x 1/2″.  You could also use new boards for this and paint them.
  • 10 coordinating nuts and bolts.  I used 1-1/2″ bolts that are treated so they won’t rust outside.  You can find these in the bins at your local hardware store.  Ask an associate if you’re not sure – the one at my store was very helpful.  Note that if you’re using thicker boards, you’re going to need longer screws.  Mine stick out about a half-inch from the back of the boards, and I’m fine with that.  However, if you’re worried about it scratching something, you need to either use shorter bolts or remove the ends after you’ve put it together (my husband’s suggestion).
  • Drill and bit, coordinating with the size of your bolts
  • Wood glue – optional
  • Clamps
  • Permanent marker
  • Gloves and eye protection  – please, please, please make sure you wear these – very important!

1.  Let’s get started!  Put on your gloves and eye protection – I am a stickler for this!  Pallets can carry harmful bacteria, and we don’t want any splinters turning into something nasty, or any bits of sawdust flying into your eyes.  I prefer to douse my pallets with a potent mix of 1 part vinegar to 1 part water and leave them to set in the sun until dry.  This will help to remove any odors as well as kill bacteria.  I know there are mixed opinions about the use of pallets for decorating.  I am very picky when choosing my pallets, and I advise you to be too.  I would never put pallet wood inside my home because of the potential hazards –  I prefer to use them to cheer things up in the garden.

2.  Once you’ve prepped, you’ll need to take your pallet apart.  This is time-consuming, but it will be worth it, I promise!  A hammer and crowbar are your best friends for this job.

OLYMPUS DIGITAL CAMERA

Make sure to remove all nails from the wood – if any are stubborn and won’t come out, make sure to either saw off the back of the nail or bend it with a hammer so that it lies flush with the board.

OLYMPUS DIGITAL CAMERA

3.  Once you’ve gotten the five pieces that you need, you’re ready to begin.  It’s really quite simple.  Remember how you drew stars without lifting your pencil when you were a kid (or, if you’re like me, still do)?  You’re simply going to do the same thing to lay out your boards, arranging and rearranging them until you’ve got them laying well.  The most important part here is to make sure that the top board at each point of the star lays pretty flush with the bottom board at each point.  You don’t want any big gaps.

OLYMPUS DIGITAL CAMERA

4.  Now you’re ready to clamp.  Place clamps at strategic points on the star so as to keep everything from moving.  It needs to be held together very well so that when you drill, nothing moves.

OLYMPUS DIGITAL CAMERA

Take a permanent marker and mark two spots on the top board of each point of the star – these are the spots where you will drill.  Make sure they are in far enough from the edge.  Just wing it.   It’s rustic – if all the bolts aren’t positioned exactly the same, it just adds charm.

OLYMPUS DIGITAL CAMERA

Now get your drill and drill a hole at each of the spots you marked – there should be 10 total.  Drill all the way through both boards.

OLYMPUS DIGITAL CAMERA

5.  Thread a bolt through each of the 10 drilled holes and secure with a nut on the back of each.  If you’d like, you can loosen the clamps in small areas at a time to squeeze some wood glue between the boards before you secure them with the nuts and bolts.  This is not necessary but may make the end result hold up better, should the wood begin to rot, or the bolt strip through at some point.

OLYMPUS DIGITAL CAMERA

6.  If you used glue, leave the clamps on overnight to allow the glue to dry.  If not, remove the clamps – you’re done!

DPP_0003

Where will you hang yours?

Advertisements

DIY Dog Bed for Senior Dogs

I have a 10-1/2-year-old Collie who is just the sweetest thing in the world, and compared to others of her breed, her health is remarkable for her age.  She still runs around the yard and barks and plays like a puppy at times, so much so that sometimes I forget how old she is.  A couple of years ago, she started having a little bit of joint stiffness during colder weather, but it’s really started to kick in this year.  It’s not even hit the 30s here yet, and she’s really showing how sore she is.

So what’s a girl to do?  I purchased her a bed about six months ago that seemed all perfectly fluffy at the store, and when it had been laid on for about 3 days, it completely de-poufed.  As in, she was sinking so far that she was basically laying on the floor with the stuffing all around her.

She needed a really good supportive bed for her joints, but they can be so expensive – for a dog her size, easily upwards of $150, and it still might not turn out to last all that well.

After spotting some great sales at my local JoAnn’s, I loaded up my coupons and headed out to get the supplies I would need to make my own.  In all, I spent just under $62 (they were having some awesome sales!).  Not bad considering the alternative.

Materials

  • 2 yards 54″-wide outdoor fabric, or other heavy-duty fabric of your choice (I chose outdoor fabric in the hopes that it will repel any accidents that may happen.  My tiny schnauzer has a habit of, ahem, regurgitating on beds that are not her own.  Not cool.)
  • 2 yards 3″ thick foam padding (the green stuff – they will cut this to size at the fabric counter for you)
  • Heavy-duty thread
  • Appropriate sewing machine needle for heavy-duty fabrics
  • 64 ounces polyester fiberfill

Step 1)  Decide the size you would like the bed to be:  I had a cover from a previous bed that I wanted to go over the new one, so I chose to use the measurements of that cover:

  • Width = 33″
  • Length = 42″
  • Height = 3-3/4″

If you are using your own cover for starting measurements, always go with the smallest measurement if there are any variations in length or width (i.e., some parts of the cover measured 33″ wide, some measured 33.5″ wide).

Step 2)  Cut pieces:  Add an inch to each measurement for seam allowances.  If you are following my measurements, fold your fabric in half and cut the following pieces, using the diagram below to show you where to make your cuts on your fabric – make sure your folded edge is in the right spot – do not cut folded edge:

a) 2 pieces for top and bottom – 34″ x 43″ (width x length)
b) 2 side pieces – 43″ x 4-3/4″ (length x height)
c) 2 end pieces – 34″ x 4-3/4″ (width x height)

Step 3)  Start sewing:

  1. Important Note:  Use a 1/2″ seam allowance at all times.
  2. Take one piece “a” and one piece “b“.  Place right sides facing and stitch a hem along one long side.  Repeat with second “b” piece on opposite side of same “a” piece.  Press seams open.  (Note:  You may wish to pin the fabric in place before stitching.  Personally, pins just get in my way, so I skip them a lot of the time.  However, if you are a new or novice sewer, I would recommend using them.)
  3. Using same piece “a” as in previous step, take one piece “c” and place right sides facing on one unsewn edge between hems for pieces “b” from previous step.  It may be a little too long.  That’s okay – just overlap each hem by an equal amount, but start and end stitching at hems – don’t go past.  It should look like this: Repeat with second “c” piece on opposite end.  Press seams.
  4. Add backing:  Place one long side of backing piece to long side of second piece “b“, right sides together; stitch.  Repeat, matching the opposite side of backing piece to second “b” piece.  After this, you should essentially have a giant tube.  It will look kind of like a giant pillow case with openings on both ends.  Repeat again with ONE shorter end, starting and stopping at the seams as on the top piece, leaving the corners of the casing pieces unstitched – we’ll come back to those later.  Here’s a hint:  If you hold the casing piece on top while you stitch, it will be much easier.  (Be careful not to catch any unwanted fabric in your stitches!)  Leave the other end unsewn until the bed has been stuffed.
  5. Stitch corners:  Starting on one corner of the closed end, match up the edges of the unsewn corner and stitch.  You may want to stitch again for reinforcement.  To do this, just put another row of stitches 1/4″ outside your seam (toward the cut edge of the fabric).  This is extra reassurance for you, just in case Poochie puts on a few pounds this winter.  In fact, you can do this to all your seams if you so desire – it’s up to you.  Repeat with the other corner on finished end.  Just a heads up: This is where my bobbin ran out (and I started with a full one), so you may want to check yours.
  6. We’re going to leave the other two corners and the opening unsewn for the time being to prepare the stuffing.

Step 4)  Stuffing:  Measure the width and length of the finished cover:

  • width = 33″
  • length = 42″

Now, subtract an inch from each number (trust me – it will be much easier to stuff if you do this), and, using a serrated knife, cut a piece of the foam the length of the bed – beware fingers and surfaces!:

  • width = 32″
  • length = 41″

Now, measure the width of the cut piece.  I needed my foam to be 32″ wide, but my foam was only 24″ wide.  To use the foam best, I cut two 6″ pieces of foam and cut them to reach a combined length that matched that of the bigger piece.  So, for the project, I used 60″ total of 24″‘-wide, 3″-thick foam.  I had purchased 2.5 yards, so I actually have enough left to make another smaller bed that would measure 31″ x 24″.

Step 6)  Stuff the bed:  Put the foam in first, unstitched hem on the bottom of the bed.  Now, if you only want a foam bed, skip to finishing the cover.  My baby, however, likes a really thick, fluffy bed (she’s not high maintenance AT ALL), so I’m going to put some fiberfill in the top.  Only fill it about 3/4 of the way.

Step 7)  Finishing:  Start hand sewing up your seam, however you prefer.  I don’t have the patience to make my stitches blind, so I just stitch a cute (albeit somewhat childlike) topstitch, making sure the seam is strong.  I have a cover that’s going over this, so honestly, I wasn’t really worried about appearance, but feel free to stitch the end shut however you want.

Voila! You’re done!  You wanna know the best part of the whole project?  Putting your feet up together when it’s done.

.-Shannon

Pinecones and the park

Hubby and I spent a leisurely morning at a park in our area recently.  It’s a great little place – never too crowded, except on those too-gorgeous-to-resist days, when the park is crawling with photographers trying to get that perfect family portrait.  You park, you walk past the playground areas, and suddenly, you come upon a covered bridge, which we don’t have many of around here.

There are picnic areas, and once you’ve crossed the bridge, if you are in a mind to go off the beaten path a bit (which we always do), there’s a little path that goes around and loops back to a gorgeous rocky area of the river.

We finished the loop and came back up the path to the covered bridge.  As per the understood laws of society, the interior is covered in “Jimmy loves Norma” in every imaginable form.

On our way into the park, you know what else I noticed they have there?  Pine cones.  That’s right.  I spent the last 15 minutes or so of our adventure picking up pine cones.  They were just so huge and perfect and fresh!  (No, I do NOT have a pine cone fetish.  At all.)  You see, I came across this wreath project awhile back that I have been just itching to make.  I mean, how beautiful is it?  And it really can stay up for two seasons – fall and winter – which makes it the perfect project for me right now.

This garland and this topiary are just two more projects I would love to make for our home.  I have gobs upon gobs of pine cones now, so I ought to be able to make several.

Hubs got a bit bored towards the end.  I tend to get tunnel vision, and that day was no exception.  He had that “Isn’t this enough pine cones?” look on his face (on other days, you may also enter “yarn” in place of “pine cones”).  But he was such a good sport about it.  That’s just one of the many things I love about him.

-Shannon

Shop Launch Sale Starts Today!

I have been busy as a little bee around here.  Sew sew sew, paint paint paint, knit knit knit.  Or maybe I’m as busy as a Christmas elf.  Getting ready for all those gift shipments.  I thrive off the busyness.  It’s fun and exciting!

As several of you no doubt know by now, I recently re-launched my Etsy shop.  I sell handmade home decor and wearables – aprons, vintage-inspired signs, pillow covers, coasters, knit hats, you name it.

For the month of October, everything in my shop is 20% off for all buyers with Etsy coupon code LAUNCH.  Simply log on to Etsy and place one (or more!) of my items in your cart.  At checkout, enter the coupon code to receive the discount.

Feel free to share the coupon code – the more, the merrier!  It’s never too early to get a jump on all that holiday shopping, and I’ll be adding new items all month long!

So stop by and say hi.  As always, thanks for reading!

-Shannon

Current Project: Granny Stripes Blanket

Hello everyone!  Lately I’ve been working on a new crocheted blanket/afghan for either our sofa or bed.  (I haven’t decided yet.  It will probably start on one and end up on the other.)  My pile of acrylic yarn (all at once now: “EWW, acrylic!”) has been piling up over the past couple of years, and though I have come to prefer more natural fibers, I just couldn’t throw out or give away all this perfectly good yarn.  I am of the mindset that acrylic has its place in the universe, and keeping me warm in the winter is now that place!

I’m going incognito as ladylovely over at ravelry, where I found this great pattern.  I know this pattern has been around for ages, but I can’t resist how cute it is or how well it lends itself to the use of multiple colors.  I have been knitting almost exclusively when it comes to yarn crafts and found that I was really missing crochet.  I have been enjoying working on this project.  I’m using several bright, cheery colors that will brighten my day in the middle of February when it’s rainy and dreary and bitter cold.

Are any of you knitters or crocheters?  If you do both, are you preferential to one over the other?  Why?  Please share – I’d love to hear!

Fall Mantle Decor

My poor mantle had somehow managed to get overlooked all summer long until suddenly I found fall staring me in the face – leaves falling, cooler nights, the whole shebang.  I was at Michael’s yesterday, and they were having a GREAT sale, so I decided to give the ol’ girl a face lift.  Tell me – what do you think?

Before…

…and after!

Inspiration and Faves, Week of 9/9 – 9/15

This morning I noticed that quite a few leaves have started to fall from the crape myrtle in my front yard and I realized the autumn season is right at our door, even here in the South.  Today I thought I’d share some of my current home decor faves for the upcoming fall season.

1. I just love the look of mercury glass, and Pottery Barn’s Champagne Mercury Glass Pumpkins caught my eye, as did the mantle display featuring these beauties alongside a rustic assortment of pumpkins, dried vine, and a variety of charming aged platters in a silver tone to complement the silver of the pumpkins.

2. Kim of ethanollie currently features a cute vintage wicker picnic basket in her Etsy shop.  This would make the perfect basket set for the picnic I have been contemplating for hubby and I this weekend.  The weather here has just been too gorgeous to pass up – I’ve been driving with the windows down and spending as much time as I can outside all week.  Anyone else?  I know I can’t be the only one…

3.  The Traveler side table from Anthropologie… what can I say?  I am a sucker for old trunks – always have been – and this would be just too cute in my living room at the end of my sofa.  Alas, the price tag does not agree with me, but a girl can dream/drool, right?

4.  I must apologize for this next one as well.  It’s definitely out of my price range, but I love to window shop even when I can’t buy.  Pottery Barn’s Clift Glass Table Lamp Base in Espresso looks just charming with the complementary Espresso Burlap Tapered Drum Lamp Shade.  I love the look of burlap, this fall more than ever.  There’s something very rustic and homey about it.

5.  Another rustic beauty, the Happy Halloween Banner from Pottery Barn is sure to charm at your autumn parties this year.  In fact, it’s inspired me to try to make my own burlap version…I’ll update on that later.

6.  Fellow crafters, beware!  I just fell in love with this paper sewing machine from Anthropologie.  Is anyone else trying to figure out how to make this out of old pattern papers?

7.  Last but not least, this rustic barbed wire heart wreath from gazaboo stole my heart too.  There is just something rustic and charming about this piece that makes it appropriate for both city and country life.

Tell me what you think!  Where are you finding inspiration as you prepare your house for fall?

Cheers – Shannon